⚡ Rapid revision — the 20-minute version
| Spine | The mark |
|---|---|
| Force types | Tension pulls, compression squashes, bending does BOTH — cracks start underneath |
| Levers | Class by position: 1 fulcrum between, 2 load between, 3 effort between |
| Moments | Effort × arm = load × arm — arms measured from the FULCRUM |
| Machines | Gain force, lose distance — gear ratio = teeth ratio |
| Structures | Triangles are inherently rigid — name struts (compression) and ties (tension) |
| Failure | Fatigue kills below normal strength — cycles, corrosion, wear |
1. Engineering — science applied under constraints
Engineering: Applying science and mathematics to build solutions that WORK within CONSTRAINTS: cost, safety, materials, time, environment. The loop: design → model → test → improve — the same iterative discipline as design & technology, with numbers attached. 'Engineers solve problems' is not the answer — 'engineers solve problems within given constraints' is.
Worked: a bridge brief — span 20 m, budget fixed, loads known. The design that is strongest AND cheapest AND safe wins; a perfect bridge that costs triple is a failed design. Name the constraint being balanced — constraint reasoning is the engineering mark.
2. Forces and loads — the five ways materials are attacked
Force types: TENSION (pulling apart — cables, ties), COMPRESSION (squashing — columns, struts), SHEAR (sliding layers — scissors, rivets), BENDING (both at once — beams: top compressed, bottom in tension), TORSION (twisting — drive shafts). STATIC loads are steady; DYNAMIC loads change (impact, vibration) and cause FATIGUE — failure below the normal strength after repeated cycles.
Worked: a shelf sagging — bending: its top surface compresses, its underside stretches in tension; that is why shelves crack from the BOTTOM. A rope in a tug-of-war is pure tension. Identify the force from the geometry; the force named with evidence is the mark.
3. Levers — three classes, one law
Levers: A lever turns about a FULCRUM with LOAD and EFFORT applied. Class 1: fulcrum between (see-saw, crowbar). Class 2: load between (wheelbarrow, bottle opener — always force-multipliers). Class 3: effort between (tweezers, fishing rod — always distance-multipliers, sacrifice force for precision and reach). The law: moments balance — EFFORT × effort-arm = LOAD × load-arm (equilibrium).
Worked: a wheelbarrow — load 600 N at 0.5 m from the wheel (fulcrum), hands at 1.5 m: effort = 600 × 0.5 ÷ 1.5 = 200 N. The arm RATIO is the mechanical advantage; class 2 multiplies force by construction. 'Which class and why' = position of the effort relative to load and fulcrum.
4. Machines — trading distance for force
Mechanical advantage: MA = load ÷ effort (force multiplier). VELOCITY RATIO = distance moved by effort ÷ distance moved by load. No machine is free: gain force, lose distance — energy in ≥ energy out (efficiency = MA ÷ VR × 100%, below 100% by friction). Pulleys: each supporting rope section shares the load (a 4-section block lifts a 800 N load with ~200 N effort). GEARS: meshed pairs reverse rotation; the ratio is the teeth ratio — a 20-tooth driver into a 40-tooth follower halves speed and doubles torque.
Worked: gears 20T → 40T: velocity ratio 2:1 — follower turns at half speed with twice the torque. Why bicycles climb in LOW gear: small front, large rear — force wins on the hill, speed on the flat. Compute the ratio from teeth; the ratio is the answer's spine.
5. Materials — properties decide, again
| Property | Meaning | Design implication |
|---|---|---|
| Strength | Resists force without failing | Load-bearing parts |
| Stiffness | Resists bending/stretching | Precision frames — vs flexible needs |
| Toughness | Absorbs impact without cracking | Hammer heads, guards |
| Hardness | Resists surface wear | Cutting edges, bearings |
| Corrosion resistance | Survives the environment | Outdoor/marine — stainless, aluminium, galvanising |
Selection = load case + environment + cost. The trap: strong ≠ tough — hardened glass is strong but shatters (low toughness); mild steel is softer but bends before it breaks. Say which property the APPLICATION needs, then name the material that carries it.
6. Structures — why everything is triangles
Triangulation: A rectangle can collapse into a parallelogram (its joints rotate); a triangle CANNOT change shape without a member changing length — triangulation makes rigid frames from pinned joints. STRUTS carry compression, TIES carry tension; trusses arrange them so every member works in its best direction. The roof truss and the bicycle frame are triangles for this exact reason — 'why triangulate?' answers itself in one sentence: triangles are the only inherently rigid polygon.
Worked: add a diagonal to a wobbly rectangular gate — the diagonal divides it into two triangles; the frame stops racking. Braces are struts or ties depending on the load direction — name which member takes which force for the mark.
7. Workshop practice — safety is a procedure, not an attitude
| Hazard | Control | Discipline |
|---|---|---|
| Flying chips/sparks | Goggles/face shield | Eye protection BEFORE the machine starts |
| Rotating parts | Guards in place, no loose clothing, tie hair | The guard you remove 'just for a second' is the accident |
| Sharp tools | Cut away from the body, sharp tools (dull ones slip) | A sharp chisel is safer than a blunt one |
| Noise/dust | Earmuffs, extraction, masks | Damage is cumulative and permanent |
| Lifting | Bend knees, load close, ask for help | Your back has no replacement part |
Work sequence: MEASURE twice → MARK OUT (scriber/pencil, datum lines from an edge) → CUT/shape → CHECK against the drawing → FINISH (deburr, sand, protect). TOLERANCE = the allowed variation ('20 ± 0.5 mm' — 19.5 to 20.5 passes): precision parts only need the tolerance they NEED, no more — tighter costs money.
8. Joining — permanent, temporary, and choosing between them
PERMANENT: welding (fuse the parent metal — strongest), brazing (filler below melting point of parent), riveting, adhesives. TEMPORARY: bolts, screws, clips — chosen for MAINTENANCE: anything that will be serviced joins with fasteners. The question 'justify the joint' = service life + loads + disassembly needs. A bolted machine frame exists because motors get replaced.
9. Failure and maintenance — how things actually die
FATIGUE: repeated cyclic loads grow micro-cracks until sudden failure — below the material's normal strength (the paperclip bent back and forth). CORROSION: electrochemical eating of metals — prevented by coating, galvanising, or sacrificial anodes. WEAR: surfaces rubbing — lubrication. MAINTENANCE: preventive (scheduled — cheaper) vs corrective (after failure — expensive). 'Why did it fail?' questions want the mechanism: cycles → fatigue; moisture → corrosion; friction → wear.
10. Summary — the engineering spine
| Question type | Method beat | Trap |
|---|---|---|
| Force type | Geometry reveals tension/compression/shear | Bending is BOTH surfaces at once |
| Lever class | Position of effort vs load vs fulcrum | Class 3 trades force for reach — not a mistake |
| Moments | Effort × arm = load × arm | Arms measured from the FULCRUM |
| Gears/pulleys | Ratios from teeth or rope sections | Force gained = distance lost |
| Materials | Property the application needs | Strong ≠ tough |
| Structures | Triangles are inherently rigid | Name strut (compression) vs tie (tension) |
| Failure | Cycles, environment, friction | Fatigue fails below normal strength |
Command discipline: 'calculate' = formula, substitution, units — no units, no mark; 'explain' = the mechanism (why triangles, why fatigue); 'justify' = the constraint evidence; 'state the class' = positions named. Engineering papers pay for UNITS and MECHANISMS — a right number with wrong units is half marks.